Matrox NRG Redundant Power Supply Unit Preinstalled On A Rack Tray
Powering multiple devices with a single RPSU
Matrox NRG is a multi-output redundant power supply unit (RPSU) that comes pre-installed on a rackmount shelf. The RPSU includes two hot swappable power supply modules and provides uninterrupted operation in case of a power module failure, and a redundant power input in case a circuit breaker trips. The NRG RPSU also features IP connectivity for status monitoring and output control. One NRG device can power up to five Matrox devices simultaneously.
Key features
- Pre-installed on a 1U rackmount shelf.
- Standard 1 RU, ½ rack width form factor.
- Includes two redundant power modules (300W each).
- Hot swappable.
- Power up to five Matrox appliances simultaneously.
- GPIO port to signal error condition.
- 10/100Base-T for remote monitoring and controlling via management software or web browser.
- Recessed rocker switch to turn the device on and off.
- Device status LEDs.
Single density
One NRG redundant power supply unit comes pre-installed on a 1U rack shelf, which can also hold a second ½ width RU (Rack Unit) Matrox device. The shelf is designed to fit standard 19" (48.26 cm) racks.
Dual density
Two NRG redundant power supply units come pre-installed on a 1U rack shelf. The shelf is designed to fit standard 19" (48.26 cm) racks.
Full redundancy for up to 5 devices
Matrox NRG includes two field-replaceable redundant power supply modules of 300W each. If one of the power supply modules fails, the output load will be completely supported by the second power module. The modules deliver hot-swap functionality, so you can replace an individual power module without interrupting the 12 volt outputs of the NRG. Automatic load balancing ensures even usage of both power supplies and extends the life of each.
Device monitoring and control
Monitor the status and control the outputs of the power supply unit remotely over IP. Through a convenient password-protected and HTTPS encrypted web interface, you can turn individual 12V outputs on and off and monitor check the status of each power supply module. An independent GPIO can also be used to monitor power module failures. The device also features LEDs that provide the status of each 12V output and AC input.
Fully compatible with Matrox products
Matrox NRG redundant power supply units support a wide range of Matrox appliances.
- Maevex 6100 Series video encoders and decoders
- Maevex 6020 Remote Recorder
- Monarch EDGE, Monarch HDX, and Monarch LCS video encoders and decoders
- Extio 3 Series IP KVM appliances
- QuadHead2Go multi-monitor controller appliances
- ConvertIP Series encoders/decoders and ST 2110 converters
Form Factor
Rack-mountable: 2 NRG units = 1U (horizontal)
Connectivity
Network Connector
1x RJ45 with status LED indicators
GPIO
GPIO output port to signal error condition
Network
Network Standard
10/100 Base-T Ethernet
IP Addressing
IPv4, DHCP (default) and static IP
Command and Control
Web-based user interface compatible with most web browsers (Google Chrome recommended)
Rest-based API for easy integration available in future release
Physical
Overall dimensions (LxWxH)
1 RU (19 x 11.45 x 1.75 inches)
(48.3cm x 29.1cm x 4.4cm)
Dimension of NRG unit on tray
8.5 x 9.6 x 1.7 inches
Unit Weight
Single unit: 6.17 lbs (2800 g)
With packaging: 9.47 lbs (4300 g)
Dual unit: 10.58 lbs (4800 g)
With packaging: 14.33 lbs (6500 g)
Additional Features
Maximum number of devices powered per NRG unit
Extio 3 Series = 4
Maevex 6100 Series = 4
Maevex 6020 = 4
Monarch EDGE Series = 4
Monarch HDX & LCS = 5
QuadHead2Go Series = 5
ConvertIP Series = 5
Power Inputs (per NRG unit)
Number of AC inputs: 2
Input voltage: 100-240V a.c.
Input frequency range: 50-60 Hz
Input current: 5A @ 115V a.c. or 2.5A @ 230V a.c.
Power Outputs (per NRG unit)
Number of DC outputs: 5
Output connector type: DIN4 female connector
Output voltage: 12V
Max current per output: output 1: 3A, outputs 2-5: 5A
Hardware & Software
NRG-5-1DB
Rack tray with one (1) pre-installed NRG RPSU
One 6 foot, double ended DIN4 cable
4 x M3 device mounting screws
4 x Tray mounting screws
NRG-5-2DB
Rack tray with two (2) pre-installed NRG RPSU
Two 6 foot, double ended DIN4 cables
4 x Tray mounting screws
Hardware Required (sold separately)
IEC 60320 C13 power cable - ships with every compatible Matrox device
Accessories (sold separately)
NRG-5-PM
Spare or replacement power module
CAB-DIN4-6FT-4
Kit of four (4) 6-foot cables with DIN4 locking connector to connect Matrox appliances to 12v RPSU outputs
Environmental
Operational Environments
Temperature: 0 to 50 C (-4 to 176 F)
Humidity: 20 to 80% (non-condensing)
Atmospheric pressure: 660hPa (3,000 meters / 9,842 feet) to 1013hPa (0 meters / 0 feet)
Storage Conditions
Non-Operational/Transportation
Temperature: -20 to 80 C (32 to 122 F)
Humidity: 10 to 90% (non-condensing)
Atmospheric Pressure: 192hPa (12,000 meters / 39,370 feet)
Power Consumption
300W max
General
EMC/EMI Compliance
Emissions: FCC part 15 class A, CISPR 32 (EN 55032) class A, ICES-003 class A
Harmonic current: IEC/EN 61000-3-2
Immunity: CISPR 35 (EN55035)
Safety approvals: CAN/CSA C22.2 No. 62368-1-14; UL 62368-1 (2014), IEC 62368-1 (Ed. 2.0)
Warranty
2 year warranty
- Rack tray with one (1) pre-installed NRG RPSU
- One 6 foot, double ended DIN4 cable
- 4 x M3 device mounting screws
- 4 x Tray mounting screws